- Posts: 5
- Thank you received: 0
- Home
- Support
- Forum
- SolidRocks / 3dsMax :: Public Section
- Technical questions
- Re-using LC and IM for animation?
- Support
- Forum
- SolidRocks / 3dsMax :: Public Section
- Technical questions
- Re-using LC and IM for animation?
Re-using LC and IM for animation?
- emartin8907
- Topic Author
- Offline
- New Member
Less
More
9 years 10 months ago #7177
by emartin8907
Re-using LC and IM for animation? was created by emartin8907
Hi,
I am in the middle of rendering a beastly animation (LC and IM took 7 days, estimated time to render the 160 frames was another 7 days) and I have to stop it for reasons out of my control to replace my hard drives with SSDs, which will be nice but damn it -_-
My question is, will I be able to re use the LC and IM? I certainly hope so!! I am about 50 frames in to the render right now.
Attached is a pic of my render settings.
I am in the middle of rendering a beastly animation (LC and IM took 7 days, estimated time to render the 160 frames was another 7 days) and I have to stop it for reasons out of my control to replace my hard drives with SSDs, which will be nice but damn it -_-
My question is, will I be able to re use the LC and IM? I certainly hope so!! I am about 50 frames in to the render right now.
Attached is a pic of my render settings.
Please Log in or Create an account to join the conversation.
9 years 10 months ago #7178
by subburb
Replied by subburb on topic Re: Re-using LC and IM for animation?
Hello !
i think yes, if LC and IM files haven't been updated or changed. I guess no.
In this case you just have to start from the desired frame and finish render.
Fingers crossed
i think yes, if LC and IM files haven't been updated or changed. I guess no.
In this case you just have to start from the desired frame and finish render.
Fingers crossed
The following user(s) said Thank You: emartin8907
Please Log in or Create an account to join the conversation.
- emartin8907
- Topic Author
- Offline
- New Member
Less
More
- Posts: 5
- Thank you received: 0
9 years 10 months ago #7179
by emartin8907
Replied by emartin8907 on topic Re: Re-using LC and IM for animation?
Where do I tell it to use the existing LC and IM files?
Please Log in or Create an account to join the conversation.
- emartin8907
- Topic Author
- Offline
- New Member
Less
More
- Posts: 5
- Thank you received: 0
9 years 10 months ago #7180
by emartin8907
Replied by emartin8907 on topic Re: Re-using LC and IM for animation?
ah, I think I figured it out. I was looking in the SolidRocks flythrough animation UI for a place to 'load from file' but instead just left the 'output' boxes empty for the LC and IM, and in the vray render settings under GI I was able to tell it to load the LC and IM from the file, and in SolidRocks in the flythrough animation ui I simply hit 'render final frames' and it loaded the LC and IM like a champ!
Cheers!
Cheers!
Please Log in or Create an account to join the conversation.
9 years 10 months ago #7181
by subburb
Replied by subburb on topic Re: Re-using LC and IM for animation?
Well, in fact, you just have to relaunch the step number 3.
DO NOT relaunch steps 1&2 because in this case IM and LC wil be computed again.
DO NOT relaunch steps 1&2 because in this case IM and LC wil be computed again.
Please Log in or Create an account to join the conversation.
- Support
- Forum
- SolidRocks / 3dsMax :: Public Section
- Technical questions
- Re-using LC and IM for animation?
Time to create page: 0.265 seconds